Skip to content

Chimney Rebuilding in Brooklyn

Serving Brooklyn and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (843) 895-6422

The short answer

Chimney rebuilding means taking damaged masonry down to sound brick and rebuilding the stack, crown, flashing and, when needed, the liner. Signs you may need it include brick flakes in the firebox, white staining, leaks and poor draft. A camera inspection tells us how far the damage goes before any work starts.

A chimney takes more weather than almost any other part of a house. Freeze-thaw cycles, wind-driven rain and years of heat slowly break down mortar joints and brick. On Brooklyn brownstones and rowhouses, the chimney stack is often the most exposed masonry on the building. When repointing and patching no longer hold, part or all of the chimney has to come down and go back up. ApexHearth's certified technicians rebuild chimneys from the crown down to sound masonry. They also check the flue so the finished chimney is safe to use, not just good looking from the street.

Signs you need it

Masonry damage often shows up inside the house before anyone climbs onto the roof to look. If you notice any of the following, have the chimney inspected before your next fire or before heat season starts.

  • Brick flakes, chunks of mortar or loose debris collecting in the firebox or at the base of the flue
  • White, chalky staining on the brick inside or outside, which means water is moving through the masonry and carrying salts with it
  • Water in the firebox, or damp spots on walls and ceilings next to the chimney after rain
  • Poor draft or smoke rolling back into the room, which can point to a damaged flue or a blockage from fallen masonry
  • A smoke or creosote smell that gets stronger on humid or rainy days, when wet masonry holds odors
  • From the street or roof: a leaning stack, missing or crumbling bricks near the top, a cracked crown, or gaps where the flashing meets the roof
Work van with chimney rods, brushes and a HEPA vacuum

What's included in a chimney rebuild

Every rebuild starts with an inspection and a written scope, so you know which courses of brick are coming down and why. A typical rebuild includes the items below. Some of them, such as a new liner, are added only when the inspection shows they are needed.

  • Camera inspection of the flue to check the liner and find damage that can't be seen from the top or the firebox
  • Removal of damaged masonry by hand, down to sound brick, with debris bagged and lowered rather than thrown off the roof
  • Rebuilding the stack with new or salvaged brick, with mortar matched as closely as practical to the existing color and joint style
  • A new crown shaped to shed water away from the flue and off the brick
  • New or reset flashing where the chimney meets the roof
  • A chimney cap to keep out rain, birds and animals
  • Liner repair or replacement when the camera shows cracks, gaps or corrosion
  • Flue cleaning with rotary brushes and a final camera check before the job is closed out
  • Cleanup of the roof, the work area and the room around the fireplace

How our crew works inside your home and on the roof

Most rebuilding happens on the roof, but the fireplace and flue are part of the job too. Before anything is touched, the crew lays drop cloths from the entry to the hearth and seals the fireplace opening. HEPA vacuums run during brushing, so soot and mortar dust are captured instead of drifting into the room. Rotary brushes clean the flue walls. A camera goes down the flue before and after the work, so you can see what we saw.

On the roof, the crew sets up safe access first. That means roof protection, ladders or scaffolding, depending on the building. Old brick and mortar come off course by course and are bagged and brought down. On attached houses we protect neighboring roofs, parapets and skylights. We keep the work area tidy at the end of each day and cover open masonry if weather moves in. Mortar needs time to cure, so we don't rush a crown or pour one into a hard freeze.

Time for your annual chimney check?

The standard we follow

We follow NFPA 211, the standard that calls for chimneys, fireplaces and vents to be inspected once a year. Chimney professionals use three inspection levels. Level 1 is for when nothing about the system has changed. Level 2 applies when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Level 3 is used when a hidden hazard can only be reached by opening part of the chimney or the building. A rebuild almost always calls for at least a Level 2 inspection, because we need to see the full flue, not just the top and the firebox.

Fuel matters too. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed, because gas exhaust produces acidic condensate that can corrode a masonry flue. If you are planning a conversion, it makes sense to look at the chimney before or alongside the rebuild.

Timing is worth planning around. New York City's heat season runs from October 1 through May 31, when building owners must keep apartments heated to the city's minimums. If your chimney serves a boiler in a building with tenants, scheduling a rebuild outside heat season avoids taking the heating system offline when it is required.

What affects the price

We give a written estimate after the inspection, because no two chimneys come apart the same way. The main factors are:

  • Chimney height and roof access, including whether scaffolding or extra roof protection is needed
  • How much masonry has to come down, from the top few courses to a full rebuild to the roofline
  • Brick and mortar matching, especially on older facades where appearance matters
  • Flue size and condition, and whether the liner can be repaired or must be replaced
  • Fuel type and the appliance the chimney serves: wood fireplace, oil or gas boiler, or water heater
  • How much creosote or soot buildup has to be cleaned before work can start
  • Whether a camera inspection or additional repairs, such as flashing, roof patching or interior water damage, are part of the job

How a visit works

First, we schedule an inspection. A technician looks at the stack, crown, flashing and firebox, runs a camera through the flue, and photographs what needs attention. You get a written scope and estimate that explain what we found and what we recommend.

Once you approve the work, we set a start date with weather and, for boiler flues, heat season in mind. The crew protects your home, sets up roof access and takes the damaged masonry down to sound brick. They rebuild the stack, crown and flashing, and handle the liner if the scope calls for it. When the masonry is done, the flue is cleaned and checked again with the camera. We walk you through the before and after photos and clean up before we leave.

Chimney sweep cleaning a brick chimney on a rowhouse roof

Book Chimney Rebuilding in Brooklyn

Serving Brooklyn and nearby cities.

  • Diagnosis before any repair
  • Written price up front
  • Written price before we start

What to expect

How a visit goes

  1. Inspection comes first

    Before we sweep, patch or replace anything, we look at the whole system and tell you what we see in plain language.

  2. Your home stays clean

    We cover the work area, run vacuum equipment that contains soot and dust, and leave the room the way we found it.

  3. You make the call

    We lay out what is urgent, what can wait and what is fine as it is, so you can decide on repairs with the full picture.

FAQ

Common questions

Don’t see your question? Call (843) 895-6422 and we’ll talk it through.

What's the difference between repointing and rebuilding a chimney?

Repointing replaces worn mortar joints while keeping the existing brick in place. Rebuilding is needed when the bricks themselves are cracked, spalling or loose, or when the stack is leaning, so the damaged section has to come down and be laid again.

How do I know how much of my chimney needs to be rebuilt?

The inspection decides that. Damage is often worst near the top, where weather hits hardest, but we take masonry down to sound brick wherever that is and show you photos of what we found.

Can I use my fireplace or boiler during the rebuild?

No. The flue is out of service while masonry is open and mortar is curing. We'll tell you when it's safe to use again, and for boiler chimneys we plan the work outside heat season when possible.

Will the new brick match my house?

We match brick and mortar as closely as practical, and we reuse sound original brick when it makes sense. On older facades, new masonry can look slightly different at first and usually blends in as it weathers.

Do I need a new liner when I rebuild my chimney?

Not always. The camera inspection shows whether the existing liner is intact. If it's cracked, has gaps, or the building is switching from oil to gas, a new liner is often needed.

Does the crew need access to the inside of my home?

Usually yes, at the fireplace or boiler connection. The crew uses drop cloths, seals the opening and runs HEPA vacuums during cleaning to keep dust out of the room.

Find Out What Your Chimney or Vents Need

Schedule an inspection and we will show you what we find, explain your options and give you a written price before any work begins.

(843) 895-6422
Call (843) 895-6422 Request Service