Skip to content

Chimney Liner Installation in Gerritsen Beach, Brooklyn

Serving Gerritsen Beach and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (843) 895-6422

The short answer

Gerritsen Beach homes usually need a new chimney liner when the original clay tiles are cracked, when there is no liner at all, or when a boiler is converted from oil to gas. ApexHearth inspects the flue, sizes a liner to the appliance, and installs it from the top of the chimney.

A chimney liner is the channel inside your chimney that carries smoke and exhaust gases up and out of the house. If it is cracked, missing, or the wrong size for the appliance connected to it, heat and combustion gases can reach the masonry and the wood framing around it. ApexHearth Chimney Services installs liners for homes in Gerritsen Beach, ZIP code 11235, about 2 miles south of our Brooklyn office. Our certified technicians inspect the flue first and explain what they find. Then they recommend a liner that matches the boiler, water heater, furnace, or fireplace it will serve.

Why Liners Fail in Gerritsen Beach Homes

Gerritsen Beach is mostly detached homes and attached houses on small lots. Many have a masonry chimney venting a boiler or water heater, and some also have a fireplace. In older chimneys, clay tile liners can crack, shift, or lose the mortar between sections after decades of heating and cooling. Some older chimneys were built with no liner at all, so exhaust touches the brick directly.

Fuel conversions are a common reason to reline. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue. A chimney that handled oil for years may not hold up once a gas appliance is connected to it.

  • Pieces of tile, crumbled mortar, or flaky debris at the base of the chimney or in the cleanout
  • Damp spots, staining, or peeling paint on walls next to the chimney
  • Water or rust stains near where the appliance vent enters the chimney
  • A planned boiler or water heater replacement, or a switch from oil to gas
  • Cracked or missing tiles found during a chimney inspection
Chimney Liner Installation at a home

Liner Options for Gas, Oil, and Wood

Most of the liners we install are stainless steel. They can be run down an existing flue even when it has slight offsets, and they are made in grades suited to gas, oil, or wood. Size matters as much as material. A liner that is too large for a modern high-efficiency boiler can let exhaust cool too much, which leads to condensation and poor draft. A liner that is too small can restrict venting. We match the diameter to the appliance's venting requirements and the height of the chimney.

Each installation includes the connections at the bottom and a top plate and cap at the crown. The cap keeps out rain and debris and stops animals from nesting in the flue.

How the Installation Works

The NFPA 211 standard calls for chimneys, fireplaces, and vents to be inspected once a year, and it defines three inspection levels. A Level 2 inspection applies when the system changes, such as a new appliance or a switch of fuel, or when the home is sold. Liner work usually starts there. If a hidden hazard can only be reached by opening part of the chimney or wall, a Level 3 inspection may be needed. We will tell you before that happens and explain why.

  • Inspect the flue, including a camera inspection, and document its condition
  • Confirm the appliance type and venting requirements, then size the liner
  • Clean the flue so the liner goes into a clear passage
  • Lower the liner from the roof and connect it to the appliance vent
  • Seal the top, install the cap, and test the draft
  • Walk you through the photos and the finished work

Time for your annual chimney check?

Planning Around Heat Season

New York City's heat season runs from October 1 through May 31. During those months, building owners must keep apartments heated to the city's minimum temperatures. If you own a two-family house in Gerritsen Beach and rent out a unit, a boiler that can't vent safely becomes an urgent problem. When possible, schedule your inspection in late summer or early fall, and plan conversions and replacements before the cold weather. If a problem turns up mid-season, call us and we will discuss how to get the system venting safely as soon as possible.

Serving Gerritsen Beach and Nearby Neighborhoods

Our crews work throughout southern Brooklyn. Besides Gerritsen Beach, we install chimney liners in Sheepshead Bay, Manhattan Beach, Madison, Marine Park, and Mill Basin. The housing in these neighborhoods ranges from detached homes to attached rowhouses and small apartment buildings. We plan each job around how the chimney is built and how the roof can be reached safely.

More services in Gerritsen Beach

Related

Chimney sweep cleaning a brick chimney on a rowhouse roof

Book Chimney Liner Installation in Gerritsen Beach

Serving Gerritsen Beach and nearby cities.

  • Diagnosis before any repair
  • Written price up front
  • Written price before we start

What to expect

How a visit goes

  1. Inspection comes first

    Before we sweep, patch or replace anything, we look at the whole system and tell you what we see in plain language.

  2. Your home stays clean

    We cover the work area, run vacuum equipment that contains soot and dust, and leave the room the way we found it.

  3. You make the call

    We lay out what is urgent, what can wait and what is fine as it is, so you can decide on repairs with the full picture.

FAQ

Common questions

Don’t see your question? Call (843) 895-6422 and we’ll talk it through.

How do I know if my chimney needs a new liner?

An inspection is the only reliable way to know. Common signs include tile fragments or debris at the chimney base, staining on nearby walls, and a planned change of appliance or fuel. A camera inspection shows the inside of the flue.

Do I need a new liner if I switch my boiler from oil to gas?

Often, yes. In New York City, the chimney has to be evaluated during an oil-to-gas conversion. Gas exhaust produces acidic condensate that can corrode a masonry flue, so a properly sized liner is frequently needed.

Can a liner be installed in a chimney that has no liner now?

In many cases, yes. A stainless steel liner can be run down an unlined masonry chimney if the passage is large enough and the structure is sound. The inspection tells us whether that will work.

How long does a chimney liner installation take?

Most residential installations take a day of work, though it depends on chimney height, roof access, and what the inspection finds. We will give you a schedule once we have seen the chimney.

Will I lose heat or hot water during the work?

The appliance connected to the chimney is shut off while we work on the flue. We will tell you in advance how long it will be off so you can plan, especially during heat season.

Do I still need yearly inspections after a new liner?

Yes. The NFPA 211 standard calls for chimneys, fireplaces, and vents to be inspected once a year, whether the liner is new or old.

Find Out What Your Chimney or Vents Need

Schedule an inspection and we will show you what we find, explain your options and give you a written price before any work begins.

(843) 895-6422
Call (843) 895-6422 Request Service